1/16 Rc GTK Boxer 8x8 styreen project

[karel47]

when i started the gtk boxer i only was planned to let open the door but saw gerhards tread when i was busy onto it

http://www.rcpanzer.de/apboard/thread.p ... =1&seite=1

he gave me some thoughts in his builds i wonna copy in my build and take it further into detailing step by step

http://www.rcpanzer.de/apboard/thread.p ... =1&seite=1









first cleaned up the reinforcementrod in the dooropening

[karel47]

first pics are gerhards onres after them my build goes further




gerhards rearhatch




my coutted out rearhatch








the real deal rearhatch

[karel47]

used minihinges from asiatam 5x5mm together 5x10mm

[karel47]

dryfitting rearhatch with boxerbody



final result and working door




real pics of the beast

[karel47]

did a few mods at Plastic and Steel modelfair

corrected the driversight it was gleud straightforward by ludwigs polisterolmadchen but it has to be under hook , so cutted it dawn , corrigated the hook and regleu it all together again it look so much better after all

[karel47]

looking at gerhards build i saw the headprotectors on the inside of the roofhatches , so i did the same , cutted them out of 1mm styreen












i will soften the edges with vallejo putty so it will look at a real headprotector

[karel47]

did some work on the rearhatch too

[karel47]

found a second donorcar for the boxer

founding the donorcar ludwig advised me but hard to get it

Truck HQ710 4WD Maßstab 1/18

Technische Daten:

Modell: RC Monstertruck " Truck HQ710" 4WD Maßstab: 1:18

Motorart: 380er Elektromotor Luftgekühlt High-Speed

Stromversorgung: 7,2V 1100mAh Ni-Cd Akku max.

Geschwindigkeit: ca.30 km/h

Fahrzeit: bis 20 Min.

Karosserie: aus Lexan

Abmessung (L x B x H): 250mm x 190mm x 110mm

http://www.gordo-toys.de/RC-Monstertruc ... -RTR-/-4WD"]http://www.gordo-toys.de/RC-Monstertruc ... -RTR-/-4WD

[karel47]

boxers drivemotor and speedcontroler



http://www.integy.com/st_prod.html?p_prodid=28380&p_catid=25&ratesortby=New#.WfIKKmi0NhE

Specifications
Type: 1/10th Brushed, Waterproof
Cont./Peak Current: 60A/360A
Input: 2-3S LiPo/6-9 Cells NiMH
BEC Output: Switch Mode:6V/3A

Wires & Connectors
Input Wires: Red-16AWG / Black-16AWG
Output Wires: Blue-16AWG / Yellow-16AWG
Input Connectors: Tamiya-style Connector
Output Connecotors: 4.0 Bullet Connectors (Female)

Size & Weight
Dimensions: 36.5x32.0x18.0mm
Weight: 39g

ESC Motor Wind Limits (540/550 Size Motors)
2S LiPo: 12-Turn and up
3S LiPo: 18-Turn and up

Included Motor
Type: Brushed
Size: 54

this gonna be my drivemotor for the boxer both watersave!!!

[karel47]

probaly gonna use these gearboxes from ebay for my scale 8x8 suspenstion





and modify two off them for an axle on the back too like gerhards one